High-impact black foot for use with square Trail Tech kickstand leg
Note:
Part number 5925-foot (Black) only fits the square Trail Tech kickstands
1. With the kickstand arm mounted to the motorcycle hold the replacement foot near the insertion hole and note rotation to allow the foot to lay flat on the ground once installed.
2. Remove the kickstand arm from bike
3. Remove old foot. This is usually accomplished by putting the foot in a vise and inserting a long screw driver or arm in the pivot bolt mounting hole and twisting it loose while pulling. To ease removal of the foot heat can be applied to the leg with a heat gun.
4. Clean and remove all oils and residue form the new foot and the kickstand foot hole
5. Use threadlocker (Surlok 1270) on the entire ribbed area that fits into the kickstand cavity to glue the foot in place
6. To insert the foot we recommend using a press. Other methods can be used. Make sure the rotation is correct and push the foot into place until it is fully bottomed against the lower flange. IMPORTANT: ALWAYS USE EYE PROTECTION WHEN USING A PRESS OR HAMMER OPERATION.
7. Wipe clean all remaining loctite
8. Remount arm to bike and insure the rotation of the foot is correct. If not use a soft jaw vice to hold the foot and twist it to the correct rotation.
9. Allow 24 hours before use of the kickstand.
Magnet Kit: Yamaha ATV Z400 KFX400 Rhino.
This carbon fiber inspired hard case is designed to tightly grip the Trail Tech Portable Air Compressor for off-road, UTV, overland and motorcycle tire inflation on the trail. Portable, lightweight, and compact, perfect for stashing in luggage, side cases or carrying bags on adventure bikes and dirt bikes. The internal mesh pocket provides storage for additional small items, including the quick-connect air trachea, valve adapters and USB charging cable.
PERFECT FIT: HARD CASE ONLY! (Portable air compressor and accessories sold separate.) This Trail Tech Hard Case is custom fitted for the Trail Tech Portable Air Compressor. The case external dimensions 9x5x3" and internal dimensions 8x4x2" expertly holds the air pump and can be stowed discreetly in your motorcycle, UTV, Jeep, SxS, truck or another wheeled vehicle.
FIRST IMPRESSION: This Trail Tech travel case is made of faux carbon fiber on the outside with soft and fluffy black fabric on the inside. Gives shockproof, waterproof, dust protection, and anti-static properties to your tire inflator. Provides travel protection for your Trail Tech tire inflator portable air compressor, valve adaptors, quick-connect trachea air tube and USB charging cable.
BEST USE: This hard case is form fitted to the Trail Tech Portable Air Compressor and features an extra mesh pocket for organizing and storing accessories, like American style quick-connect trachea, valve adapters, storage bag and USB charging cable.
COMPATIBLE: The Trail Tech Air Compressor Hard Case has a small handle and is compact in shape. Perfect for stowing in motorcycle bags, car trunk or in a backpack. It is very convenient for tire pump storage and bringing to your next outdoor adventure.
Voyager/Vapor Ignition Sensor 2550mm Length (100").
Type
Voyager & Vapor ignition Sensor
Physical Features
Wire Length 1800mm
(70.87%u201D)
Voyager/Vapor/Endurance II Power Connection 1220mm (4in).
Type
Voyager Power Lead
Physical Features
Wire Length 1220mm
Speed sensor cable extension 600mm (24") long.
Type
Extension for Speedometer Cable Male to Female
Physical Features
Wire Length 600mm
(24%u201D)
Temperature sensor extension lead 600mm (24") long.
Type
Extension for Temperature Sensor Male to Female
Physical Features
Wire Length 600mm
(24%u201D)
Temperature sensor extension lead 1800mm (72") long.
Type
Extension for Temperature Sensor Male to Female
Physical Features
Wire Length 1800mm
(72%u201D)
Temperature sensor extension lead 1200mm (48") long.
Type
Extension for Temperature Sensor Male to Female
Physical Features
Wire Length 1200mm
(48%u201D)
Voyager/Vapor Ignition Sensor 1800mm Length (70.87in).
Type
Voyager ignition Sensors
Physical Features
Wire Length 1800mm
Mounting bracket for Vapor/Striker, vertical surface attachment.
Ideal for mounting to KTM.
Endurance II Replacement Handle Bar Mounting
Type
Handlebar Mounting Hardware For Endurance II
Physical Features
Handlebar Diameters 7/8"
1-1/8"
Are you in need of long hoses for your Trail Tech Portable Off-Road Air Compressor? Look no further! Our long hoses will be the perfect addition to your off-roading kit. Here are some reasons why:
Investing in a pair of long hoses for your Trail Tech Portable Off-Road Air Compressor is a smart move for any off-road enthusiast. Don't let a lack of reach hold you back from exploring the trails. Order your long hoses today and experience the convenience and versatility they offer!
Voyager/Vapor handlebar mounting hardware. Included in every Voyager kit. Fits 1-1/8'' - 7/8'' handlebars.
Positions Voyager/Vapor in the center of the controls, in the safe zone below the bars.
Type
Handlebar Mounting Hardware For Voyager GPS
Physical Features
Handlebar Diameters 7/8''
1-1/8''
Voyager Top Triple Clamp Mount Bracket for perches bolted on and 100-106mm spacing.
Triple clamp mounting bracket. Mount Voyager to front of triple clamp of most off-road motorcycles.
Fits most KTMs and other motorcycles where the number plate screws into the front of the triple clamp. If a headlight or number plate spacer is present, there should be plenty of room. On some models with a very close number plate, some modifications may be necessary (add spacer or notch the number plate.)
Digital gauge sold separate.
Voyager Pro plastic handlebar mounting hardware kit for 7/8 and 1-1/8 bars.
Included in Voyager Pro kits.
Patented mount design has two points of articulation, enabling a wide variety of mounting positions.
Made from special high strength materials to withstand the rigors of powersports.
Includes screws and bolts to attach a Voyager Pro dock.
Comes with four M4x14mm screws to attach the Voyager Pro dock.
Included in Voyager Pro kits.
Voyager Pro GPS unit not included.
Off Road Imports © 2024