Micro SD Card Reader.

High-impact black foot for use with square Trail Tech kickstand leg

Note:

Part number 5925-foot (Black) only fits the square Trail Tech kickstands

1. With the kickstand arm mounted to the motorcycle hold the replacement foot near the insertion hole and note rotation to allow the foot to lay flat on the ground once installed.

2. Remove the kickstand arm from bike

3. Remove old foot. This is usually accomplished by putting the foot in a vise and inserting a long screw driver or arm in the pivot bolt mounting hole and twisting it loose while pulling. To ease removal of the foot heat can be applied to the leg with a heat gun.

4. Clean and remove all oils and residue form the new foot and the kickstand foot hole

5. Use threadlocker (Surlok 1270) on the entire ribbed area that fits into the kickstand cavity to glue the foot in place

6. To insert the foot we recommend using a press. Other methods can be used. Make sure the rotation is correct and push the foot into place until it is fully bottomed against the lower flange. IMPORTANT: ALWAYS USE EYE PROTECTION WHEN USING A PRESS OR HAMMER OPERATION.

7. Wipe clean all remaining loctite

8. Remount arm to bike and insure the rotation of the foot is correct. If not use a soft jaw vice to hold the foot and twist it to the correct rotation.

9. Allow 24 hours before use of the kickstand.

Fits: Generic

Magnet Kit: Yamaha ATV Z400 KFX400 Rhino.

Magnet Kit: KTM motorcycles.

Muc-Off Technical Wash is a wash-in cleaner that safely removes dirt, grime, and odours from your technical gear. The unique, concentrated formula gives your garments a deep but safe clean, whilst protecting any existing DWR treatments and the breathability of the material, so it's perfect for freshening up and extending the life of those shred threads! It can be used on any technical or waterproof/water repellent fabric including Gore-Tex®, Polartec®, Pertex®, eVent®, softshell and hardshell clothing.

Features:

• Gently removes dirt and grime from technical apparel
• Extends life and performance of garments
• Can be used on any technical or waterproof/water repellent fabric
• Can be used in the washing machine or applied by hand
• Suitable for use in hard and soft water areas
• Will not impact breathability of garments
• Biodegradable formula
• PFC-Free 
• Not harmful for the environment or to you
• Safe to use on any garments with an existing DWR treatment
• Perfect to use as a pre-wash ahead of reproofing your technical apparel with Rain Shield Re-Proofer Spray or Wash-In Rain Shield Re-Proofer

Instructions for Use:

1. Place garments to be washed into your washing machine.
2. Shake bottle well to activate the formula.
3. Use 25ml (5 x 5ml/0.16oz capfuls) per wash load.
4. Dispense Technical Wash for Apparel directly into the detergent drawer of your washing machine, in place of normal washing detergent.
5. Wash on a full cycle at 30°C/86°F or according to care label instructions.
6. Allow garments to air-dry. 

TOP TIP

If washing water repellent/waterproof garments we'd recommend re-treating with our Wash-In or Spray-On Rain Shield ReProofer after the wash to restore the water repellent finish. Follow the directions for use on the bottle for application details.

This carbon fiber inspired hard case is designed to tightly grip the Trail Tech Portable Air Compressor for off-road, UTV, overland and motorcycle tire inflation on the trail.  Portable, lightweight, and compact, perfect for stashing in luggage, side cases or carrying bags on adventure bikes and dirt bikes.  The internal mesh pocket provides storage for additional small items, including the quick-connect air trachea, valve adapters and USB charging cable.

PERFECT FIT: HARD CASE ONLY! (Portable air compressor and accessories sold separate.) This Trail Tech Hard Case is custom fitted for the Trail Tech Portable Air Compressor.  The case external dimensions 9x5x3" and internal dimensions 8x4x2" expertly holds the air pump and can be stowed discreetly in your motorcycle, UTV, Jeep, SxS, truck or another wheeled vehicle.

FIRST IMPRESSION: This Trail Tech travel case is made of faux carbon fiber on the outside with soft and fluffy black fabric on the inside.  Gives shockproof, waterproof, dust protection, and anti-static properties to your tire inflator.  Provides travel protection for your Trail Tech tire inflator portable air compressor, valve adaptors, quick-connect trachea air tube and USB charging cable.

BEST USE: This hard case is form fitted to the Trail Tech Portable Air Compressor and features an extra mesh pocket for organizing and storing accessories, like American style quick-connect trachea, valve adapters, storage bag and USB charging cable.

COMPATIBLE: The Trail Tech Air Compressor Hard Case has a small handle and is compact in shape.  Perfect for stowing in motorcycle bags, car trunk or in a backpack.  It is very convenient for tire pump storage and bringing to your next outdoor adventure.

• Portable Air Compressor Sold Separate
• Hard Case for Compressor
• Carbon Fiber Pattern
• Tight Fit with Zipper
• Inner Mesh Pocket

Voyager/Vapor Ignition Sensor 2550mm Length (100").

Type

Voyager & Vapor ignition Sensor

Physical Features

Wire Length 1800mm

(70.87%u201D)

Voyager/Vapor/Endurance II Power Connection 1220mm (4in).

Type

Voyager Power Lead

Physical Features

Wire Length 1220mm

Speed sensor cable extension 600mm (24") long.

Type

Extension for Speedometer Cable Male to Female

Physical Features

Wire Length 600mm

(24%u201D)

Temperature sensor extension lead 600mm (24") long.

Type

Extension for Temperature Sensor Male to Female

Physical Features

Wire Length 600mm

(24%u201D)

Temperature sensor extension lead 1800mm (72") long.

Type

Extension for Temperature Sensor Male to Female

Physical Features

Wire Length 1800mm

(72%u201D)

Temperature sensor extension lead 1200mm (48") long.

Type

Extension for Temperature Sensor Male to Female

Physical Features

Wire Length 1200mm

(48%u201D)

Voyager/Vapor Ignition Sensor 1800mm Length (70.87in).

Type

Voyager ignition Sensors

Physical Features

Wire Length 1800mm

Mounting bracket for Vapor/Striker, vertical surface attachment.

Ideal for mounting to KTM.

Endurance II Replacement Handle Bar Mounting

Type

Handlebar Mounting Hardware For Endurance II

Physical Features

Handlebar Diameters 7/8"

1-1/8"

Are you in need of long hoses for your Trail Tech Portable Off-Road Air Compressor? Look no further! Our long hoses will be the perfect addition to your off-roading kit. Here are some reasons why:

1. Increased Reach: With longer hoses, you'll be able to reach your tires even if they are further away from the compressor. This makes it easier to fill up your tires and get back on the road or trail.
2. Versatility: Longer hoses give you more flexibility when it comes to inflating different tires. Whether you need to inflate the tires on your ATV, truck, or trailer, our long hoses will be able to handle the job.
3. Durability: Our hoses are made with high-quality materials that are designed to withstand the wear and tear of off-roading. You can be confident that our hoses will hold up even in rugged terrain.
4. Convenience: Our long hoses come with quick-connect fittings that make it easy to attach them to your Trail Tech Portable Off-Road Air Compressor. This means you'll be able to set up and inflate your tires quickly and easily.

Investing in a pair of long hoses for your Trail Tech Portable Off-Road Air Compressor is a smart move for any off-road enthusiast. Don't let a lack of reach hold you back from exploring the trails. Order your long hoses today and experience the convenience and versatility they offer!

• Hose Length: 15" (480mm)
• Material: Rubber with braided nylon covering
• Valve Type on Hoses: One hose with Schrader screw, the other hose with lock-on air chuck for Schrader valves. Compatible with Presta adapter and ball needle in Trail Tech Portable Air Compressor kits.

Voyager/Vapor handlebar mounting hardware. Included in every Voyager kit. Fits 1-1/8'' - 7/8'' handlebars.

Positions Voyager/Vapor in the center of the controls, in the safe zone below the bars.

Type

Handlebar Mounting Hardware For Voyager GPS

Physical Features

Handlebar Diameters 7/8''

1-1/8''

Voyager Top Triple Clamp Mount Bracket for perches bolted on and 100-106mm spacing.

Triple clamp mounting bracket. Mount Voyager to front of triple clamp of most off-road motorcycles.

Fits most KTMs and other motorcycles where the number plate screws into the front of the triple clamp. If a headlight or number plate spacer is present, there should be plenty of room. On some models with a very close number plate, some modifications may be necessary (add spacer or notch the number plate.)

Digital gauge sold separate.